Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
What're your thoughts and feelings on Installing A Bathtub?

Installing a tub isn't exactly rocket science, yet it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is readily easily accessible, the task can relocate quickly; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the task and also are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to think about employing one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This post will certainly help you set up a new bathtub in your bathroom if you have actually already bought a new tub and do not need to change the arrangement of your previous water system pipes.
Your devices and material checklist ought to consist of the following:
Planning for the Setup
Firstly, the supporting frame supplied with the bath should be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be quite bothersome due to the limited gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using the two wood boards under its feet, put the tub in the called for setting. The wood boards are valuable in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the water supply and also inspect all joints as well as new pipework for leakages and tighten them if essential. Load the bath tub and also examine the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the maker's user's manual. Tiling and also sealing around the tub must wait until the bathtub has been used a minimum of once as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer provided backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a rigid seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to issues with moisture and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof glue and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

I hope you enjoyed reading our topic on How to Install a Bathtub. Thank you so much for spending some time to read through our article. Those who enjoyed reading our post if you please be sure to pass it around. We take joy in reading our article about How to Install a Bathtub Yourself.
Set Up An Appointment Report this page